CantusManualBack to the site

Pulsus III: pads on their own strips, a chain per pad, kits from anywhere

Cantus 0.1.0-beta.12 · Leer en español · back to the manual

Pulsus is Cantus's drum instrument: up to 32 pads, each a synthesised drum or samples. This chapter is about three things a drum kit needs in a mix: each pad on a mixer strip of its own, effects on one pad before the kit is summed, and kits made from your own samples — a folder of one-shots or an SFZ kit.

Split to strips

Open the kit (double-click its track) → ⋯ ▸ Split to strips, or right-click the kit's strip in the mixer → Split to strips. Every pad that makes a sound gets a strip of its own, named after the pad, placed right after the kit's strip, in the order of the pads. Each pad now has its own fader, pan, inserts, sends, mute and solo. One undo step.

The pad strips play into the kit's strip: the kit's strip is the kit's bus, so a compressor or a fader there still acts on the whole kit, and the kit's track still mutes and solos all of it. With every new strip at 0 dB and centred, the split kit sounds exactly like the kit did before — not nearly: the same samples, to the bit (with the kit track's own level at 0 dB and its balance centred; at another level the two agree to within −120 dB). A pad's strip pans as a balance (its pan law is 0 dB), so it passes the pad untouched; the kit's strip places the kit through the project's pan law as before. The strip's menu says which law it follows (Pan law ▸), and lets you change it.

Merge back (the same menus) undoes Split to strips: it puts every pad the split moved back on the kit's strip and removes the strips the split made — unless something else uses one (a send into it, another track). A pad you sent to a mixer track of your choosing (its Mixer track in the channel rack) stays there: that routing is yours, and Merge back leaves it alone. To bring such a pad back, choose The kit's strip as its mixer track. One undo step.

Good to know:

Older kits. A kit made before this version is Model 2 (or Model 1). It splits too, but sums to itself only within rounding (about −135 dB); Upgrade to Pulsus III in the kit's header makes it exact. Nothing else changes.

One pad on a mixer track of its own (as in FL Studio)

Round 40. In the channel rack every pad of a kit has its mixer track's well, left of its name, as every channel has: it reads the strip the pad plays on — the kit's number until you choose another (a kit on strip 3 shows "3" on each of its pads). Click a pad's well to choose:

The pad then plays there and only there: the kit's strip, its inserts and fader no longer touch that pad; the strip chosen does (its fader, inserts, sends, mute and solo). A pad with a chain keeps it: the chain plays into the strip chosen. One undo step; saved with the song. Choosing the kit's strip again puts the pad back exactly as it was, to the bit.

Split to strips (above) does the same for every pad at once, into new strips that play into the kit's strip; the well chooses one pad, and any strip. A strip a pad leaves stays in the desk with its inserts (delete it there if you no longer need it).

A chain per pad

Select a pad and open Edit: the Chain card lists the pad's own inserts, in order. Add insert ▾ puts any Cantus effect at the end (with its starting preset); each insert has its switch, Edit (its editor) and Remove. The pad's sound goes through its chain before it joins the kit — or before it goes to its own strip, when the kit is split; split and merge keep the chain on its pad. Once the pad has a chain, More… opens the device picker onto it: every effect, plug-ins included.

A chain costs nothing while its pad is silent: Cantus does not run its inserts until the pad plays again, and what comes out is exactly what running them would give.

A chain follows its kit: route the kit's track to another strip and every chain goes with it. Add insert ▾ offers what a strip offers (Spatium is the reverb).

Kits from your samples

A folder. Drag a folder of one-shots from the file manager onto a kit's pads: it becomes that kit. Drop it anywhere else in the window: it becomes a new kit track. Cantus reads the names, in English or Spanish:

A name withGoes to
kick, bd, bombo, bass drumKick (note 36)
rim, rimshot, side stick, aroRim (37)
snare, sd, caja, redoblanteSnare (38)
clap, palmasClap (39)
hat / hh / hihat / charles + closed, cerradoClosed hat (42)
… + pedal, foot, piePedal hat (44)
… + open, abiertoOpen hat (46) — the three hats choke each other
tom + low/floor/grave, tom, tom + high/agudoToms (41…50)
crash, splash, china · ride · cowbell, cencerro49 · 51 · 56
perc, shaker, pandereta, conga, bongó, clave, maraca…Percussion (54, 58, 60…)

Files that differ only by a number (Kick 1, Kick 2) become one pad that takes them in turn (round robin) — except a number that names the drum: Tom 1, Tom 2, Tom 3 (high to floor), Crash 1, Crash 2 and a leading one (808 Kick, 909 Kick) are pads of their own. Files that differ by a dynamic (soft, medium, hard, pp, mf, ff, vl1…vl4, suave, fuerte) become one pad's velocity layers, the softest for the softest hits. A name that says nothing goes on the next free pad, in the folder's order. Up to 32 pads and 16 layers a pad; what does not fit is named in the log. One undo step. A folder is read in the background; one of more than 512 sounds (or 4 GB) is not a kit and is refused, and a folder dropped away from a kit's pads must name a drum in some file.

An SFZ kit. Drag an .sfz file the same way: one pad per key, its regions as layers (velocity ranges, tuning, level, pan), round robins and random choices kept, and the kit's exclusive groups (a hi-hat's) as a choke group. Tested with the free Virtuosity Drums kit.

The factory kits

The kit's header lists the sixteen factory kits: Pulsus classic, Studio, 808, 909, Boom bap, Electro, Percussion, Trap, House, Lo-fi, Rock, Pop, R&B, Reggaeton, Cinematic and Jazz brushes — every one synthesised by Pulsus itself, no samples. Each comes with its own Kit level (the kit card), calibrated; 0 dB on a kit of your own changes nothing. ⋯ ▸ Browse presets… opens the preset browser on the kit: filter by style, listen to a kit before you choose it, load it in one undo step.

For agents

split_kit_outputs (and merge), set_pad_chain (add or remove an insert on a pad) and make_kit_from_folder (a folder or an .sfz, only inside the project's folder or a folder you allowed in Settings ▸ AI, with file access on) do the same, one undo step each — see What an AI agent can do.